Interface Modules

• The Trigger is a universal module that provides 15 different preset functions that are activated from a positive or negative trigger.
• In addition to the preset features the Trigger has 8 custom modes with customizable settings that allows the installer to utilize their imagination.

Descriptions of modes and wiring instructions

• Default: EBrake Emulator
• Mode 1: Retained accessory power - Device will turn on and stay on at all times when the accessory turns on and will not turn off until the door opens or 10 minutes passes, whichever first
• Mode 2: Delayed amp turn-on - When the input is activated, there will be a 2-second delay before pin-8 turn-on.
• Mode 3: Low voltage turn-on - Provides 12 volts turn on from a low voltage source
• Mode 4: Latched outputs - Allow the capability of making a pulsed signal a latched signal.
• Mode 5: GMLAN aftermarket amp turn-on - Provides an amp turn on in LAN vehicles for adding an aftermarket amp.
• Mode 6: Active edge pulse generator - Allow the capability of making an input signal a pulse signal.
• Mode 7: Turn-off delay - When the output is turned off, the pin-8 will stay active for two additional seconds.
• Mode 8: Double pulse latch - Device will turn on when accessory turns on, and will not turn off until door opens or 10 minutes passes, whichever comes first.
• Mode 9: Double pulse to one-second output - Converts a double pulse output to a single pulse output.
• Mode 10: Theft detection/closed loop trigger - When connected, if item loses ground the Trigger will send out a 12 volt constant signal which can be hooked to an audible device.
• Mode 11: Channel expander - Gives the ability to add additional channels to an alarm, etc.
• Mode 12: Simple data detector (amp turn-on signal from data) - Produces a positive or negative signal out when data is detected.
• Mode 13: Long delayed turn-off (for headlights) - This mode will keep headlights on for 1 minute after ignition is turned off.
• Mode 14: Dome light delay - Keeps dome light on for 30 seconds after ignition is turned off.
• Mode 15: Custom program - Ability to custom program the Trigger using the Trigger program. Note: USB-CAB is required

Custom program modes:

• Custom Mode 1: Channel expander/ latched - Measures pulses that occur during 5 second interval. One pulse per 5 seconds will toggle pin-6 (Green), two pulses per 5 seconds will toggle pin-7 (Red), and three pulses per 5 seconds will toggle pin-8 (Blue).
• Custom Mode 2: Channel expander/ pulsed - Measures pulses that occur during 5 second interval. One pulse per 5 seconds will drive pin-6 (Green) active for XX seconds, two pulses per 5 seconds will drive pin-7 (Red) active for XX seconds, and three pulses per 5 seconds will drive pin-8 (Blue) active for XX seconds. XX is definable between .1 and 300 seconds.
• Custom Mode 3: Delayed turn-off- Connect active high input to pin 9, or active low input to pin 10. Use any output pin. When input goes high, output will turn on immediately. When input goes inactive, output turn-off will be delayed by XX seconds, where XX is definable between .1 and 300 seconds.
• Custom Mode 4: Delayed turn-on - Connect active high input to pin 9, or active low input to pin 10. Use any output pin. When input goes high, output will turn on after a delay of XX seconds. When input goes inactive, output turn-off will be immediate. XX is definable between .1 and 300 seconds.
• Custom Mode 5: Delayed three-output delay/pulse width/ edge driven (for use with linear actuators) - When either input goes active, each output will go active after a delay, and then stay active for a pulse width. Each output has an independent delay and pulse width, definable between .1 and 300 seconds.
• Custom Mode 6: Generic three-output delay/pulse width/ level driven (validity) - When either input goes active, each output will go active after a delay, and then stay active for a pulse width. Each output has an independent delay and pulse width, definable between .1 and 300 seconds.
• Custom Mode 7: Square wave-generator (sounds horns/ blinks lights) - When either input goes active, all three outputs will toggle every XX seconds, where XX is definable between .1 and 300 seconds. Stops when input goes inactive.
• Custom Mode 8: Multiple pulse generator - A single input pulse on either input will produce multiple pulses on all outputs. The number of pulses can vary from 1 to 255, and each pulse will last XX seconds, where XX is definable between .1 and 300 seconds.